Extending the hull mold flange with Aqua Steel so it’s ready for vacuum infusion. #NuWaveComposites #AquaSteel #VacuumInfusion #MoldMaking #CompositeBoatBuilding | NuWave Composites
0:10
Extending the hull mold flange with Aqua Steel so it’s ready for vacuu…
3.5K views3 months ago
FacebookNuWave Composites
Hull mold in process. You can see the vacuum pump we use to prevent any pre-release on our molds. This is commonly used in parts as well. Pre release can happen due to a variety of factors, excessive mold release, temperature change, resin shrink etc. #boats #fiberglass #howitsmade | NuWave Composites
0:14
Hull mold in process. You can see the vacuum pump we use to preve…
80.1K views6 months ago
FacebookNuWave Composites
Buffing the Aqua Steel flange to bring the hull mold up to a high-gloss finish so it’s vacuum infusion ready. #NuWaveComposites #AquaSteel #VacuumInfusion #BoatMold #CompositeTooling | NuWave Composites
0:12
Buffing the Aqua Steel flange to bring the hull mold up to a high-gl…
2.6K views3 months ago
FacebookNuWave Composites
1st lower hull infusion Sept. 30, 2012
5:02
1st lower hull infusion Sept. 30, 2012
57.3K viewsOct 26, 2012
YouTubePacksail
Modern Hulls: Thin but Strong! The Vacuum Infusion Secret #boatbuilding #boatbuilder
0:27
Modern Hulls: Thin but Strong! The Vacuum Infusion Secret #boatbuil…
190 views2 months ago
YouTubeMetan Marine and Builder of the Classic Collect…
#Vacuuminfusion (also known as vacuum-assisted resin transfer molding or VARTM) is a closed-mold composite manufacturing process where dry fiber reinforcements (like fiberglass or carbon) are laid in a mold, sealed under vacuum, and then impregnated with resin. This method pulls out air voids, ensures even resin distribution, and achieves a precise fiber-to-resin ratio (often around 50/50 or better), resulting in parts that are stronger, lighter, and more uniform than traditional hand-layup tech
0:28
#Vacuuminfusion (also known as vacuum-assisted resin transfer m…
66.9K views5 months ago
FacebookMetan Marine and The Classic Collection
J/45 Infusion of first hull using SCRIMP vacuum-bag system
1:05
J/45 Infusion of first hull using SCRIMP vacuum-bag system
8.2K viewsSep 27, 2021
YouTubeStuart Johnstone
0:37
Watch till the end to see the hull part that was vacuum infused from thi…
3K viewsApr 9, 2025
FacebookNuWave Composites
0:19
Vacuum infusion on an XPC hull #XPCBoat #VacuumInfusion #Co…
1.9K views2 months ago
YouTubeNuWave Composites
9:30
Fibreglass vacuum moulding.
2.2M viewsJul 18, 2009
YouTubeEastCoastFibreglass
10:42
Vacuum Resin Infusion of a 100 foot Hull - By Marathon Pacific Marines
57.6K viewsNov 10, 2011
YouTubeMarathon Pacific Marines
10:19
Vacuum Moulding with Fiberglass - How to - Tutorial
29.2K viewsOct 7, 2016
YouTubehopsenrobsen
0:25
Check out the process of this hull mold frame! #manufacturing #cust…
92.2K views5 months ago
FacebookNuWave Composites
Introduction to Vacuum Forming
May 18, 2020
formlabs.com
21:22
Sail Life - DIY building a rudder for a sailboat, vacuum infusion - part 1 …
73.3K viewsMar 10, 2019
YouTubeSail Life
15:02
Vacuum Bagging a Carbon Fiber/Composite Part - Complete …
96.8K viewsMay 27, 2021
YouTubefreemanmfg
1:18
Vacuum Infused Lamination - Boat Production Process
22.2K viewsDec 7, 2018
YouTubeCenturion Boats
0:39
Simulation of vacuum resin infusion of a 39' trimaran main hull
4.4K viewsJan 10, 2012
YouTubeFramF39
15:34
How To Make A Fiberglass Mold For Making New Parts On Your Boat!!
781.9K viewsMar 27, 2018
YouTubeBoatworksToday
2:15
Fittings for Vacuum Bagging Overveiw
16.4K viewsSep 2, 2014
YouTubeFibre Glast
7:13
Vacuum Bagging a Transom Tutorial with Fiberglass Supply
24.9K viewsNov 19, 2022
YouTubeLindell Adventures
3:27
Infusion Molding with Reusable Silicone Vacuum Bag
36.5K viewsMar 1, 2018
YouTubeElkem Silicones
18:34
Sail Life - Vacuum and heat🔥 to deal with osmosis (DIY version of HotV…
73.9K viewsJul 9, 2017
YouTubeSail Life
0:24
We vacuum the hull mould to make a carbon fiber hull for our catamaran
9.6K viewsFeb 4, 2024
YouTubeThe Engineer
1:25
The Vacuum Forming Process
24.2K viewsMay 7, 2015
YouTubeToolcraft Plastics Ltd - Plastic Injection Mouldin…
12:04
EP-5 WE ARE BUILDING A NEW BOAT! HOW TO SEPERATE A FIB…
152.8K viewsFeb 8, 2022
YouTubeFish Bump TV
8:08
How To Mold Fiberglass & Composites 3 of 8
244.3K viewsOct 9, 2008
YouTubeFibre Glast
4:41
How To Mold Fiberglass & Composites 4 of 8
251.8K viewsOct 9, 2008
YouTubeFibre Glast
14:47
How To Do Perfect Vacuum Resin Infusion of a Carbon Fibre Part - B…
1.4M viewsDec 19, 2010
YouTubeEasy Composites Ltd
7:12
How to vacuum bag
98.5K viewsJul 16, 2018
YouTubeAero3DTech
See more videos
Static thumbnail place holder